To pair Bytech wireless earbuds, remove both earbuds from the charging case, they power on automatically and enter pairing mode, which is the fastest way to connect them to your phone, tablet, or computer for the first time. If you need to pair bytech wireless earbuds again after a failed attempt, place them back in the case, close the lid, wait a few seconds, and repeat the process.
Before you pair your Bytech wireless earbuds
Make sure the earbuds have enough battery power before starting. Place them into their charging case and connect the included USB cable to a power source. The indicator light on the case or earbuds will show charging status. Leave them until the light indicates a full charge, this prevents connection drops during pairing. Also, keep the earbuds within the typical Bluetooth transmission range of up to 33 feet (10 meters) from your device, and turn off Bluetooth on any other devices nearby that might interfere.
How to put Bytech earbuds in pairing mode
The automatic pairing process is the simplest method. Remove both earbuds from the charging case, they will power on and enter pairing mode without pressing any buttons. Model-specific indicator lights tell you what is happening. For the BY-AU-BE-225-AC model, one earbud flashes red and blue while the other stays off, confirming they have synced to each other. For the BY-AU-BE-173 model, both lights flash initially, then only one stops flashing to signal pairing mode. Some models flash white on both earbuds. If you do not see these lights, check your model’s manual for instructions on forcing pairing mode. Remember that the earbuds will automatically shut down if they are not connected to a device after approximately 5 minutes in pairing mode, so complete the next step quickly.
Connecting to your phone, tablet, or computer
- On your smartphone, tablet, or computer, navigate to the Bluetooth settings.
- Turn Bluetooth ON.
- Search for new devices in the Bluetooth settings.
- Select the Bytech earbuds from the list of available devices. The name will typically start with "Bytech" or "BY-BE-" followed by a model number, for example, "BY-BE-225" for the BY-AU-BE-225-AC model, "BY-BE-224" for the BY-AU-BE-224-AC model, "BY-BE-173" for the BY-AU-BE-173 model, "BY-BE-705" for the BY-AU-BE-705 model, "BYTECH BLUTOOTH EARBUDS" for some models, or "iHome XT-10" for the XT-10 model. The BYTECH BC-AU-BE-146-WT model appears as "BYTECH BC-AU-BE-146-WT" or a similar name.
- Wait for the connection to complete. Once successfully paired, you will hear a confirmation tone or voice prompt, and the indicator lights will stop flashing or flash blue slowly (for the XT-10 model, the LEDs flash blue to indicate connection).
If prompted for a password during pairing, enter "0000" for some models. After the first connection, your device will remember the earbuds, so future pairing is automatic.
Why are my Bytech earbuds not connecting?
If the connection fails, work through these troubleshooting steps in order. First, ensure the earbuds are charged and out of the case, low battery or earbuds still inside the case will prevent pairing. Next, toggle Bluetooth off and on again on your device to refresh the connection. If that does not work, forget the earbuds from your device’s Bluetooth list and attempt to pair again from scratch. For one earbud not working, place both earbuds back into the charging case, close the lid, wait a few seconds, then take them out again, this resets the sync between the two buds. Ensure no other devices are connected to the earbuds, as a single pair can only maintain one active connection at a time. If the pairing voice prompt does not appear, consult your model’s manual for instructions on re-entering pairing mode. Also, Bluetooth devices may not connect if they are out of range or not in pairing mode, so keep your device within 33 feet and confirm the lights are flashing. If the earbuds power off during troubleshooting, remember they shut down after about 5 minutes of no connection, put them back in the case and start again. If you still have issues, your device’s software may need an update, or you may need to consult the user manual for a factory reset specific to your model. If you own a different brand, the process to pair JBL wireless earbuds follows a similar reset-and-sync logic. For persistent problems, Bytech customer support can provide model-specific guidance.
Using your Bytech earbuds after the first pairing
For subsequent uses, the earbuds will automatically connect to the last paired device when removed from the case, provided Bluetooth is enabled on your device and it is within the 33-foot range. Just take them out and they will reconnect without any steps. If you want to switch to a different device, you will need to put the earbuds back into pairing mode by placing them in the case and removing them again, then select them from the new device’s Bluetooth list. The automatic reconnection works for the most recently used device only, if you pair with a second phone, the earbuds will prioritize that one until you pair again. Keep the earbuds charged, and they will continue to auto-connect every time you take them out, giving you instant wireless audio. If you ever need to use a different brand, you can similarly use JBL wireless earbuds by following their own pairing steps, or pair jlab wireless earbuds with the same Bluetooth settings menu.
